How do I reset ap9617 APC?
you need to push the reset button, the status LED will flash rapidly. When that happens, you need to push the reset button a second time, where then the LED will go off. at that time, go to your serial connection in hyperterminal and keep pressing enter until presented with a username and password prompt.
How do I reset my APC password?
Press the Reset button a second time immediately while the LED is rapidly flashing – which will cause the LED to then go off – in order to reset the User Name and Password to their defaults temporarily (the default User Name and password are both apc).
How do I reset my APC UPS Nic?
Locate the APC network management interface on the back of your APC UPS. Press the reset button for 20 seconds. Wait for the network led change to the orange color. The APC UPS network management interface will reset its configuration back to the factory default.
How do I log into APC?
APC: First-time login to an APC device
- Configure your PC using a static IP address on the 192.168.
- Open a web browser and enter the default IP address of the AP device—192.168.2.66:
- Once the login page is loaded, enter the default administrator login information (login: admin; password: admin01) and click Login:
How do I access APC Smart UPS?
Open your browser and enter the IP address of the APC UPS. After a successful login, you will be sent to the APC UPS Dashboard. Configure the desired static IP address an click on the Apply button.
How do I factory reset my APC PDU?
Resetting APC AP7920 PDU
- Press and hold the reset button for about 10 seconds.
- The status light should blink rapidly.
- Release the reset button then press it again for about a second.
- The light should go orange.
- After about 20 seconds the reset will complete and the device will have booted.
How do I log into APC UPS?
Connect to the UPS/device serial port using the correct APC configuration cable….9600 bps, 8 data bits, no parity, 1 stop bit, and no flow control.
- Apply the port settings to establish the connection.
- Press enter 3-5 times to display the username prompt.
- Use the default username and password of “apc”.
What is the default IP address for apc PDU?
By default, the APC AP7900 does not have an IP address assigned. The easiest way to configure an IP address is to log into the PDU over a serial port. Most servers still come with a built-in 9-pin serial port, but most desktops and laptops do not….Old Firmware.
| System IP | 10.20.2.1 |
|---|---|
| Default Gateway | 10.20.255.254 |
What is the default IP of APC UPS?
192.168.2.66
The default IP address is 192.168. 2.66 with a subnet mask of 255.255. 255.0.
What is the default IP address for APC PDU?
What is APC AP9617 network management card Ex?
The APC AP9617 Network Management Card EX is a web-based management product that uses multiple, open standards such as Telnet, HTTP, and SNMP to provide full management of supported devices: – Provides a Data Log accessible by FTP or a Web browser. – Detects connection speed of 10/100 MB per second.
What is the default username and password for APC card?
The default username:password on the APC card is apc:apc. You can configure it through the UPS it’s installed in via the proper APC (black) serial cable. Please don’t use a generic 9-pin cable.
How do I reset the user name and password on AP9606?
(*If you are using an AP9606, proceed to step 7.) Press the Reset button again a second time immediately while the LED is rapidly flashing – which will cause the LED to then go off – in order to reset the User Name and Password to their defaults temporarily (the default User Name and password are both apc).
What is the difference between AP9618 and AP9619?
AP9618 features The AP9618 Network Management Card EM/MDM includes the analog modem and Integrated Environmental Monitor features described on page 4. AP9619 features The AP9619 Network Management Card EM includes the Integrated Environmental Monitor features described on page 4; the AP9619 does not include the analog modem feature.