How do you use the cat eye speedometer?

How do you use the cat eye speedometer?

1. 1 Clear all data (initialization) Press the AC button on the back of the computer.
2. 2 Select the speed units. Select “km/h” or “mph”.
3. 3 Enter the tire circumference. Enter the front wheel tire circumference of your bicycle in mm.
4. 4 Set the clock.
5. 2 3.
6. 60 cm.
7. 5 mm.
8. 2 Install the sensor and magnet.

Where do you put a Cateye sensor?

The speed (cadence) sensor can be mounted either on the top or bottom of the chain stay. If the speed (cadence) sensor is mounted on the bottom of the chain stay rather than on the top, the adjustment range between the sensor and the magnet will be narrower.

How do you program a Cateye Strada slim?

Press the MENU button and the MODE button on the back of the computer. Press the AC button on the back of the computer. After full lighting of the screen, the computer switch- es to the speed unit setting screen to start setup.

How do you set up a Cateye Strada slim?

Why is my Cateye Strada flashing?

It indicates the sensor battery is running down. Replace the coin battery with a new one and press the RESET button on the sensor.

How does a Cateye bike computer work?

It uses a wired speed sensor that attaches to the front fork and a small spoke magnet to record speed. Nothing fancy, just the basics, but it gets the job done and can be purchased for less than the price of mounting brackets for other computers.

How do I reset my Cateye wireless?

Long press (2 sec.) 1 Clear all data. Press the AC button on the back of the computer. * All data is deleted and the computer is reset to its factory default settings.

How do I turn off the Cateye light on my bike?

To remove the light unit, pull out it forward while pressing * the button. To re-adjust the beam angle, loosen the dial enough * to move the bracket, and securely tighten it after adjustment. CAUTION!: Be sure to tighten the dial by hand.

How do I set up Cateye Micro Wireless?

Press the AC button on the back of the computer. After full lighting of the screen, the computer switch- es to the speed unit setting screen to start setup. When the MODEbutton is pressed, either “km/h” or “mph” is selected for the speed unit display. Select the display of your choice.

How do I turn off Cateye Strada?

1. From the measurement screen, press MENU to switch to the menu screen. Measurement screen.
2. Press MODE to display the screen shown below, and then press MODE for 2 seconds. (2 seconds)
3. Switch off the functions you want to skip by moving to the relevant icon and turning the setting off.
4. Press MENU to confirm settings.

What do you think of the new Cateye Strada Slim?

CatEye Strada Slim wireless computer. CatEye say that the new Strada Slim is “smooth, sleek & slimmed down – like the riders and bikes its designed for”. Portly mountain-bikers look away now, then. This is an evolution of the existing (and excellent) Strada wireless computer rather than a new model.

Is the Strada Slim a good computer for cyclists?

The Strada Slim is a decent value, particularly for the cyclist who will not take advantage of the advanced features offered on more expensive computers. If you are road cyclist or casual cyclist looking for a basic computer, then the Strada Slim may be a good fit.

How to perform the all clear operation on the Strada slimcc-rd310weng?

CATEYE STRADA SLIM CYCLOCOMPUTER CC-RD310W Battery case cover Dot section MENU AC MODE L mm STRADA SLIMCC-RD310WENG 2 Perform the All Clear operation, when you use the unit for the fi rst time or restore the unit to the condition checked at the factory. Preparing the computer 1 Clear all data (initialization)

What is the slim sensor on the Strada wireless?

with slim sensor. All of the same great features as the Strada Wireless in a thinner, lighter design that incorporates a larger screen and display! The slim sensor designed specifically for road bike use virtually disappears inside the fork.