What is a XAUI interface?
10Gb Ethernet Attachment Unit Interface or XAUI is a high-speed interconnect that offers reduced pin count and has the ability to drive up to 20 inches of PCB trace on standard FR-4 material.
What is the speed of an XAUI interface?
The Xilinx 10 Gigabit Attachment Unit Interface (XAUI) LogiCORE™ IP provides a 4-lane high speed serial interface, providing up to 10 Gigabits per second (Gbps) total throughput.
What is Xgmii?
10 gigabit media-independent interface (XGMII) is a standard defined in IEEE 802.3 designed for connecting full duplex 10 Gigabit Ethernet (10GbE) ports to each other and to other electronic devices on a printed circuit board (PCB). It is now typically used for on-chip connections.
What is dual GB Ethernet?
Bonding Dual Gigabit Ethernet This enables your computers to view them as a single interface, using one gigabit connection to send and the other to receive. This arrangement effectively doubles your input to 2 Gbps if you’re using gigabit cards, or 20 Gbps if you’re using 10 GB cards.
What is 10G WAN PHY?
10G WAN PHY operates at a data rate compatible with SONET OC-192c and SDH STM-64, but 10G LAN PHY does not. “Ekinops’s 10G protocol converter enables direct connectivity of 10G LAN PHY equipment, such as 10-Gigabit Ethernet switches, to SONET/SDH networks,” said Didier Bredy, CEO of Ekinops.
What does Sgmii mean?
The Serial Gigabit Media Independent Interface (SGMII) is a connection bus for Ethernet Media Access Controllers (MACs) and Physical Layer Devices (PHYs) defined by Cisco Systems. It replaces the classic 22-wire GMII connection with a low pin count, 4-pair, differential SGMII connection.
What does an Ethernet PHY do?
The Ethernet Physical Layer (PHY) is responsible for the physical link between the Ethernet controller and the network. This layer is onchip on the FT900 so only the differential signals are available at pin level. The magnetics allow different nodes on the Ethernet network to connect over long distances.
What is the difference between XFP and SFP?
“XFP” stands for “10 Gigabit Small Form Factor Pluggable” while “SFP” stands for “Small Form-factor Pluggable.” Both modules can provide you greater signal strength in your computer network, and telecommunication links.
Who developed XFP?
XFP, a powerful technique for the study of macromolecular structures and dynamics of proteins and nucleic acids in solution, is relatively new to the ALS, though it was first developed more than 10 years ago by scientist Mark Chance at the NSLS.
Why do you need dual Ethernet?
Dual Ethernet capabilities enable network administrators to install a router and 3G/4G cell modem on the secondary Ethernet port to provide cellular connectivity. Alternatively, the DSM-40NM-E console server is now available with internal 4G LTE connectivity for private LTE networks.
Why do I need dual Gigabit Ethernet?
Can cat5 do 10Gb?
So, unless you think you might need 10 Gigabits across a given link, Cat5e will do the trick just fine. Cat5e can even handle 10 Gigabit Ethernet at short distances, so within a server room for example as a backbone link, Cat5e cable is rated to handle it.
Does CAT6 support 10Gb?
Therefore, CAT6 has now become the minimum standard for new cabling installations. As well as being able to easily support 1 Gbps network speeds, CAT6 can also support higher data rates of 10Gbps. However, 10Gbps is only supported over shorter distances of 37-55 metres.
Is Sgmii a SerDes?
SGMII support on the MPC8313E is provided through an internal Serializer-Deserializer (SerDes) PHY that converts the parallel data stream into a serial stream.
What is MII RMII?
MII vs RMII for Ethernet Therefore, RMII (reduced MII) was developed as a variant of MII to cut the number of unshareable signals per PHY interface in half (down to 8 per PHY). The RMII specification is also capable of supporting 10 Mbps and 100 Mbps data rates, and there are gigabit-capable variants.