How do you install a DITRA drain?
Schlüter-DITRA-DRAIN is cut to size, embedded in the applied adhesive and immediately pressed into the thin bed adhesive with a float or a roller. When working with Schlüter-DITRA-DRAIN 4, ensure that the inverted truncated pyramid shaped chambers are completely filled with adhesive after installation.
How long should DITRA set before tiling?
How long do I have to wait before I can install tile on the Schluter®-DITRA membrane? Once DITRA has been installed on the substrate, tile can be installed right away. No need to wait for the mortar to cure.
Is Schluter DITRA worth it?
DITRA provides reliable waterproofing in interior and exterior applications. Its polyethylene composition protects the substrate from moisture penetration, which is particularly important in today’s building environment where most substrates are moisture sensitive.
How does Ditra drain work?
Balconies / terraces As an uncoupling and drainage memb- rane, Schlüter-DITRA-DRAIN neutralises the stresses between the substrate and the tile covering that are caused by frequent, major temperature changes on balconies.
What do you put DITRA down with?
For example, to set DITRA over plywood or OSB, a modified thin-set mortar meeting the requirements of ANSI A118. 11 is used. To set DITRA over concrete or gypsum, Schluter-Systems recommends an unmodified thin-set mortar meeting the requirements of ANSI A118. 1.
How thick should subfloor be under DITRA?
DITRA is 1/8″ (3 mm) thick, which minimizes tile assembly thickness and reduces transitions to lower surface coverings (e.g., carpet, engineered wood, and vinyl).
What do you use under DITRA?
For example, to set DITRA over plywood or OSB, a modified thin-set mortar meeting the requirements of ANSI A118. 11 is used. To set DITRA over concrete or gypsum, Schluter-Systems recommends an unmodified thin-set mortar meeting the requirements of ANSI A118.
How far is linear drain from wall?
It is installed directly against the wall, so that the channel body support is in contact with the wall. The drain outlet is approximately 2 1/8″ o.c. from the edge of the wall board.
Does Schluter make a black linear drain?
Schluter-Systems is expanding its family of matte black products by introducing two new grates that are available for its Kerdi-Line linear drain. The Solid and Square grates are now available in matte black, in a variety of sizes.
Can you level on top of DITRA?
No, any leveling of the subfloor must be done prior to installing the DITRA-HEAT membrane.
What is Ditra drain made of?
Schluter DITRA DRAIN is a drainage membrane designed specifically for use with thin-bed ceramic and stone tile installations in exterior applications. Ditra-Drain is made of a studded polyethylene sheet with a laminated polypropylene filter fabric.
What is Ditra-drain?
Schlüter-DITRA-DRAIN is a safe and permanently effective passive capillary drainage system for floor assemblies. The material is installed in exterior areas into thin bed adhesive over a sloped waterproofing assembly, such as Schlüter-KERDI or other suitable proprietary waterproofing systems.
How much does Schluter Ditra-drain cost?
Schluter DITRA-DRAIN is a drainage membrane designed specifically for use with thin-bed ceramic and stone tile assemblies in exterior applications. Shipping: $29.95 Flat rate ground shipping for unlimited Schluter products in this order. Some exclusions apply. (More Info)
How to use Schlüter-Ditra-drain 4?
Schlüter-DITRA-DRAIN is cut to size, embedded in the applied adhesive and immediately pressed into the thin bed adhesive with a float or a roller. When working with Schlüter-DITRA-DRAIN 4, ensure that the inverted truncated pyramid shaped chambers are completely filled with adhesive after installation. Observe the curing times of all materials.