How do you take care of a newly plastered pool?
Brush the pool twice a day for the first two weeks. This opens the pores of the plaster to allow proper curing as well as removes any loose plaster dust from the surface. You may notice plaster dusting when you brush and the water becomes cloudy. This is normal and will go away with proper treatment and brushing.
How long does new pool plaster take to cure?
Curing plaster refers to a maturation process of the new plaster finish when it strengthens and seals. The pool finish will start to cure immediately after mixing. Sixty percent of the curing process occurs in the first 4 weeks and will continue over the next 8 to 10 months.
How soon can I add chemicals after plastering pool?
Operate filtration system continuously for a minimum of 72 hours. DO NOT add chlorine for 48 hours. DO NOT turn on pool heater until there is no plaster dust in the pool.
How soon can you swim in a newly filled pool?
Chlorine/non-chlorine chemicals – When adding chlorine or non-chlorine chemicals to “shock” your pool after a fill-up, wait about 24 hours or until levels are approximately 5 ppm. If you’ll only be adding liquid chlorine, it’s generally safe to swim after about 4 hours or until levels are 5 ppm or lower.
When can I start brushing new plaster?
Clean filter after vacuuming. After 72 hours add the CYA and then the chlorine SLOWLY to gradually bring it to the desired level. Continue to brush, vacuum, test water balance, and clean the filter for one to two weeks, or 3 days after you see no plaster dust coming off when you brush.
When should I start brushing my new pool?
A startup procedure is the 28-day process of caring for a new pool plaster finish after the pool is filled with water. During this time, you’ll need to test your water regularly, maintain the chemical balance, brush the pool to remove plaster dust, and avoid using automated equipment.
Do you shock a brand new pool?
When opening your pool in the spring – When a pool is first opened, the chlorine level normally needs an immediate boost, and shock is the quickest and easiest way to accomplish this. If the chlorine level is already adquate, a non-chlorine shock may be used to treat the water.
How do I treat my pool for the first time?
Chemicals Needed for Pool Start Ups
- Stain & Scale Preventer.
- Granular Shock Chlorine.
- Chlorine Tablets.
- pH Increaser and/or pH Decreaser.
- Alkalinity and/or Calcium Increaser.
- Cyanuric Acid (Stabilizer)
- Algaecide and Clarifiers if needed.
- Complete Test Kit or Test Strips.
Does new pool plaster absorb water?
New installations and drained pools: A common appearance of cracking can occur when a cementitious interior finish is wetted prior to being filled. Microscopic shrinkage cracks (micro cracks are present in all hardened plaster, precast, shotcrete, and concrete products) absorb water faster than the overall surface.
Does pool plaster need to stay wet?
I. The importance of this cannot be overemphasized. If the water is stopped, your plaster could develop a permanent ring at the level where the water stopped, or it could allow the exposed plaster to dry too quickly, and cause chips or cracks. Plaster is especially formulated to stay underwater at all times.
Should you shock a brand new pool?
What happens if it rains on new pool plaster?
Rain will cause streaks, discoloration, and curing mistakes once the plastering has begun. Not only will it cause streaking, but it also causes something called hydrostatic holes in the granite and plaster.
How do you brush a new plaster pool?
– Optional Anti-scaling Product. If you’re filling your pool with fresh water, this is a good time to add an anti-stain or anti-scaling product. – Adjust the pH. – Adjust Total Alkalinity. – Sanitize the Water. – Adjust Hardness. – Add Algaecide.
How do you repair plaster on a pool?
Empty the pool
What to do After plastering a pool?
Drain. The first step of the swimming pool resurfacing process is draining the pool.
How to fix pool plaster?
Stains. Most plaster pools are lightly colored like blue,white or gray.